ZyXEL Communications 2002 Series Guide de l'utilisateur Page 125
- Page / 161
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
VES-1000 Series Ethernet Switch
VDSL-Related Commands 12-11
Table 12-7 Ethernet Speed Parameters
SPEED INDEX NUMBER SPEED/FLOW CONTROL
0 Auto Negotiation
1 10 Mbits/s, Half Duplex
2 10 Mbits/s, Full Duplex
3 100Mbits/s, Half Duplex
4 100Mbits/s, Full Duplex
12.3.4 Enet Fctrl Command
vdsl enet fctrl chan-id (lt|nt) [on|off]
Type this command to set the Ethernet port flow control or show the Ethernet port flow control status (without
“on” or “off”). By default, flow control is on for full duplex Ethernet connections and off for half duplex Ethernet
connections.
Figure 12-10 Ethernet Flow Control
12.3.5 Enet Monitor Command
vdsl enet monitor chan-id [on|off]
When this flag is on this command automatically displays the VES-1000 Series switch (and the subscriber’s
VDSL modem’s Ethernet statistics if the link is up) every five seconds. Enter the command without “on” or “off”
to just show the Ethernet monitor status.
Figure 12-11 Ethernet Monitor Status
ves-100>vdsl enet monitor 2
enet monitor flag: off
ves-100>vdsl enet fctrl 2
enet flow control(LT): on
- VES-1000 Series 1
- Copyright 2
- ZyXEL Limited Warranty 3
- FCC Interference Statement 4
- FCC Warning 4
- CE Mark Warning: 4
- Taiwanese BCIQ A Warning: 4
- Certifications 4
- Customer Support 5
- Table of Contents 6
- Table of Contents vii 7
- List of Figures 9
- List of Diagrams 12
- List of Tables 13
- List of Tables xv 15
- Preface 16
- Related Documentation 17
- Getting Ready 19
- Chapter 1 21
- Switches 21
- 1.2 Applications 23
- 1.2.2 Enterprise Application 24
- 1.2.3 Campus Application 25
- Chapter 2 27
- Hardware 27
- Connections 27
- 2.3 Front Panel 28
- 2.4 Front Panel Ports 28
- 2.4.1 Console Port 29
- 2.4.2 VDSL Port Connections 29
- 2.5 Front Panel LEDs 30
- Hardware Connections 2-5 31
- Chapter 3 33
- Introducing 33
- the SMT 33
- 3.3 SMT Menus At A Glance 34
- Getting Started 38
- Chapter 4 39
- General 39
- Switch and IP Setup 39
- 4.2.1 Ethernet Port Trunking 41
- 4.2.4 GARP Timer Setup 44
- 4.2.5 GVRP 45
- 4.2.6 VLANs 45
- Port-based VLANS 46
- Tagged VLANs (IEEE 802.1Q) 46
- 4.2.7 IGMP Snooping 47
- 4.3 TCP/IP Setup 49
- Chapter 5 53
- 5.1.4 Ethernet Port Setup 56
- 5.2 Port Submenus 57
- Part III 61
- Chapter 6 63
- Route Setup 63
- 6-2 Static Route Setup 64
- Chapter 7 65
- 7.2.1 Static VLAN Setup 66
- Chapter 8 69
- Configuration 69
- 8.2 Supported MIBs 70
- 8.3 Configuring SNMP 70
- 8.4 SNMP Traps 71
- 8-4 SNMP Configuration 72
- Table 8-3 SNMP Traps 72
- System Maintenance 74
- Chapter 9 75
- Maintenance 1 75
- 9.2.1 System Maintenance 76
- Port Statistics 77
- 9-4 System Maintenance 1 78
- Table 9-2 Port Statistics 78
- System Maintenance 1 9-5 79
- 9.2.3 VLAN Status 81
- 9.3.1 System Information 83
- 9.4 Log and Trace 84
- 9.4.2 UNIX Syslog 85
- 9.5 Diagnostic 86
- System Maintenance 1 9-13 87
- Chapter 10 89
- Firmware 89
- and Configuration File 89
- Maintenance 89
- 10.2 Backup Configuration 90
- 10.2.4 GUI-based FTP Clients 92
- 10.2.7 TFTP Command Example 93
- 10.3 Restore Configuration 94
- 10.3.2 FTP Restore Example 95
- 10.4.1 Firmware File Upload 97
- 10.4.5 TFTP File Upload 99
- HyperTerminal 102
- Chapter 11 105
- Maintenance 2 105
- 11.2.1 Resetting The Time 106
- 11.3.1 Secured Client Sets 107
- 11.4 Hardware Monitor 109
- Commands 115
- Chapter 12 115
- VDSL-Related 115
- 12.2 VDSL Commands 116
- 12.2.1 Set VDSL Mode 117
- 12.2.4 Reset a VDSL Channel 118
- 12.2.7 VDSL Version Command 120
- 12.2.9 VDSL Show Command 120
- 12.2.11 VDSL Debug Command 121
- 12.3.4 Enet Fctrl Command 125
- 12.3.5 Enet Monitor Command 125
- Chapter 13 127
- Switch-Related 127
- 13.3 Port Status Command 128
- 13.4 VLANs 129
- SYMBOL DESCRIPTION 130
- 13.4.2 VLAN Set Command 131
- Sw vlan set 3 1 132
- Sw vlan set 4 1 132
- 13.4.3 VLAN Clear Command 133
- Sw vlan clear 1 3 4 134
- Sw vlan clear 1 all 134
- 13.5 MAC Address Commands 135
- 13.6 MAC Address Learning 136
- 13.6.1 MAC Address Details 137
- 13.6.2 MAC Number 137
- 13.8 Switch Driver Commands 139
- TxFreeCnt = 79287 140
- Chapter 14 141
- 14.1.2 IGMP Snooping Queries 143
- 14.1.3 Enable IGMP Snooping 143
- Chapter 15 145
- Troubleshooting 145
- 15.4 Data Rate 146
- 15.5 Configured Settings 146
- 15.6 Password 146
- 15.7 Remote Server 147
- 15.8 Telnet 147
- 15-4 Troubleshooting 148
- Appendices and Index 150
- Appendix A 151
- Hardware Specifications 151
- • 4.4 kg 152
- • 35 watts maximum 152
- • 100-240VAC/1A, 50/60Hz 152
- Appendix B 153
- Pin Assignments 153
- F Appendix B 156
Produits connexes et manuels pour Mise en réseau ZyXEL Communications 2002 Series
(10 pages)
(140 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels