ZyXEL Communications 2002 Series Guide de l'utilisateur Page 116
- Page / 161
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
VES-1000 Series Ethernet Switch
12-2 VDSL-Related Commands
Figure 12-2 CI Commands
12.2 VDSL Commands
The following table is a summary of VDSL-related commands.
Table 12-2 VDSL-related Commands
COMMAND DESCRIPTION
vdsl uprate chan-id (x)
This command sets the VDSL upstream rate (0 to 4)
vdsl downrate chan-id (y)
This command sets the VDSL downstream rate (0 to 4)
vdsl reset chan-id [lt|nt]
This command resets the VDSL chip.
vdsl reconnect chan-id
Make VDSL reconnect
vdsl clear chan-id
Clear VDSL related counters
vdsl debug chan-id [on|off]
This command sets the VDSL debug flag.
vdsl monitor chan-id [on|off]
This command sets the VDSL monitor flag.
vdsl status chan-id
This command shows the VDSL status counters.
vdsl show chan-id
This command shows VDSL settings.
vdsl mode chan-id (mode)
This command changes the VDSL mode (0 = 10BaseS, 1 = ANSI, 2
= ETSI).
vdsl active chan-id [on|off]
This command actives/deactivates the VDSL driver.
vdsl ver
This command shows the VDSL driver version.
vdsl quality chan-id
This command shows VDSL quality.
vdsl enet status chan-id
This command shows Ethernet status counters.
vdsl enet clear chan-id
This command clears Ethernet status counters.
vdsl enet monitor chan-id [on|off]
This command sets the VDSL chip Ethernet monitor flag
vdsl enet phy chan-id
This command shows the NT Ethernet PHY registers.
“chan-id” (“vdsl01”, “vdsl02”,…”vdsl12”) refers to the channel name for each VDSL channels. “all” is also a
valid channel name that indicate all channels.
All VDSL parameters and flags set using VDSL commands are effective at run-time only. If you
restart the VES-1000 Series switch, you will lose the configuration changes you made with
commands. To save changes permanently, please use the appropriate SMT menu.
The rest of this chapter shows commonly used VDSL-related CI command examples.
ves1012> ?
Valid commands are:
sys exit ether vdsl
ip sw prot
ves1012>
- VES-1000 Series 1
- Copyright 2
- ZyXEL Limited Warranty 3
- FCC Interference Statement 4
- FCC Warning 4
- CE Mark Warning: 4
- Taiwanese BCIQ A Warning: 4
- Certifications 4
- Customer Support 5
- Table of Contents 6
- Table of Contents vii 7
- List of Figures 9
- List of Diagrams 12
- List of Tables 13
- List of Tables xv 15
- Preface 16
- Related Documentation 17
- Getting Ready 19
- Chapter 1 21
- Switches 21
- 1.2 Applications 23
- 1.2.2 Enterprise Application 24
- 1.2.3 Campus Application 25
- Chapter 2 27
- Hardware 27
- Connections 27
- 2.3 Front Panel 28
- 2.4 Front Panel Ports 28
- 2.4.1 Console Port 29
- 2.4.2 VDSL Port Connections 29
- 2.5 Front Panel LEDs 30
- Hardware Connections 2-5 31
- Chapter 3 33
- Introducing 33
- the SMT 33
- 3.3 SMT Menus At A Glance 34
- Getting Started 38
- Chapter 4 39
- General 39
- Switch and IP Setup 39
- 4.2.1 Ethernet Port Trunking 41
- 4.2.4 GARP Timer Setup 44
- 4.2.5 GVRP 45
- 4.2.6 VLANs 45
- Port-based VLANS 46
- Tagged VLANs (IEEE 802.1Q) 46
- 4.2.7 IGMP Snooping 47
- 4.3 TCP/IP Setup 49
- Chapter 5 53
- 5.1.4 Ethernet Port Setup 56
- 5.2 Port Submenus 57
- Part III 61
- Chapter 6 63
- Route Setup 63
- 6-2 Static Route Setup 64
- Chapter 7 65
- 7.2.1 Static VLAN Setup 66
- Chapter 8 69
- Configuration 69
- 8.2 Supported MIBs 70
- 8.3 Configuring SNMP 70
- 8.4 SNMP Traps 71
- 8-4 SNMP Configuration 72
- Table 8-3 SNMP Traps 72
- System Maintenance 74
- Chapter 9 75
- Maintenance 1 75
- 9.2.1 System Maintenance 76
- Port Statistics 77
- 9-4 System Maintenance 1 78
- Table 9-2 Port Statistics 78
- System Maintenance 1 9-5 79
- 9.2.3 VLAN Status 81
- 9.3.1 System Information 83
- 9.4 Log and Trace 84
- 9.4.2 UNIX Syslog 85
- 9.5 Diagnostic 86
- System Maintenance 1 9-13 87
- Chapter 10 89
- Firmware 89
- and Configuration File 89
- Maintenance 89
- 10.2 Backup Configuration 90
- 10.2.4 GUI-based FTP Clients 92
- 10.2.7 TFTP Command Example 93
- 10.3 Restore Configuration 94
- 10.3.2 FTP Restore Example 95
- 10.4.1 Firmware File Upload 97
- 10.4.5 TFTP File Upload 99
- HyperTerminal 102
- Chapter 11 105
- Maintenance 2 105
- 11.2.1 Resetting The Time 106
- 11.3.1 Secured Client Sets 107
- 11.4 Hardware Monitor 109
- Commands 115
- Chapter 12 115
- VDSL-Related 115
- 12.2 VDSL Commands 116
- 12.2.1 Set VDSL Mode 117
- 12.2.4 Reset a VDSL Channel 118
- 12.2.7 VDSL Version Command 120
- 12.2.9 VDSL Show Command 120
- 12.2.11 VDSL Debug Command 121
- 12.3.4 Enet Fctrl Command 125
- 12.3.5 Enet Monitor Command 125
- Chapter 13 127
- Switch-Related 127
- 13.3 Port Status Command 128
- 13.4 VLANs 129
- SYMBOL DESCRIPTION 130
- 13.4.2 VLAN Set Command 131
- Sw vlan set 3 1 132
- Sw vlan set 4 1 132
- 13.4.3 VLAN Clear Command 133
- Sw vlan clear 1 3 4 134
- Sw vlan clear 1 all 134
- 13.5 MAC Address Commands 135
- 13.6 MAC Address Learning 136
- 13.6.1 MAC Address Details 137
- 13.6.2 MAC Number 137
- 13.8 Switch Driver Commands 139
- TxFreeCnt = 79287 140
- Chapter 14 141
- 14.1.2 IGMP Snooping Queries 143
- 14.1.3 Enable IGMP Snooping 143
- Chapter 15 145
- Troubleshooting 145
- 15.4 Data Rate 146
- 15.5 Configured Settings 146
- 15.6 Password 146
- 15.7 Remote Server 147
- 15.8 Telnet 147
- 15-4 Troubleshooting 148
- Appendices and Index 150
- Appendix A 151
- Hardware Specifications 151
- • 4.4 kg 152
- • 35 watts maximum 152
- • 100-240VAC/1A, 50/60Hz 152
- Appendix B 153
- Pin Assignments 153
- F Appendix B 156
Produits connexes et manuels pour Mise en réseau ZyXEL Communications 2002 Series
(10 pages)
(140 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels